Device Identification

Device: Wave Pro Shutter

• US Part number/Ordering Code: QPSH-0A1P10US
• Z-Wave Product type ID: 0x0003
• Z-Wave Product ID: 0x0084
• Z-Wave Manufacturer: Shelly Europe Ltd.
• Z-Wave Manufacturer ID: 0x0460

---

Terminology

• Device – In this document, the term “Device” refers to the Shelly Qubino device that is the subject of this guide.
• Gateway (GW) – A Z-Wave™ gateway, also referred to as a Z-Wave™ controller, Z-Wave™ main controller, Z-Wave™ primary controller, or Z-Wave™ hub, etc., is a device that serves as a central hub for a Z-Wave™ smart home network. The term “gateway” is used in this document.
• S button – The Z-Wave™ Service button, located on Z-Wave™ devices and used for various functions such as adding (inclusion), removing (exclusion), and resetting the device to its factory default settings. The term “S button” is used in this document.
• Adding/Inclusion – The process of adding a Z-Wave device to a Z-Wave network (gateway). Words like included, added, etc., are used in this context.
• Removing/Exclusion – The process of removing a Z-Wave device from a Z-Wave network (gateway). Words like excluded, removed, etc., are used in this context.

---

Short Description

[Error: User '712020:515aa595-e304-41f3-886a-d9b6b0b7f5a3' does not have permission to view the page 'DEV:About the Device'.]

---

Manual Operation for Shutter

Manual Operation with Momentary Switch

• Parameter No. 71 set to 0
• Parameter No. 1 set to 0

Actions:

• Pressing the push-button connected to SW1 (up) for less than 0.5 seconds (short press) initiates upward movement.
• Pressing the push-button connected to SW2 (down) for less than 0.5 seconds (short press) initiates downward movement.
• If the shutter is moving, any press (on any push-button) will stop the movement.
• Pressing SW1 for more than 0.5 seconds (long press) starts upward movement until the button is released.
• Pressing SW2 for more than 0.5 seconds (long press) starts downward movement until the button is released.

Action Table:

Action on Push-Button	Blind Not Moving	Blind Moving Up	Blind Moving Down	Tilting Slats Ongoing
Short press (UP)	Start moving up	Stop moving	Stop moving	No action
Short press (DOWN)	Start moving down	Stop moving	Stop moving	No action
Long press (UP)	Start moving up (incl. slat tilt for venetian)	Moving	Moving	Tilting to end → move UP
Long press (DOWN)	Start moving down (incl. slat tilt for venetian)	Moving	Moving	Tilting to end → move DOWN
Release after long press	No action	Stop moving	Stop moving	Stop tilting

---

Manual Operation with Toggle Switch

• Parameter No. 71 set to 0

• Parameter No. 1 set to 1

• Pressing the toggle switch connected to SW1 (up) initiates upward movement until released.

• Pressing the toggle switch connected to SW2 (down) initiates downward movement until released.

---

Manual Operation for Venetian Blinds with Momentary Switch

• Parameter No. 71 set to 1
• Parameter No. 1 set to 0

General Rules:

• Short press (< 0.5 s): initiates blind movement
• Long press (> 0.5 s): initiates slats rotation

Actions:

• Short press (SW1 UP): start moving up
• Short press (SW2 DOWN): start moving down
• Long press (SW1 UP): initiate slats rotation (0% → 100%), time defined by Parameter No. 72
• Long press (SW2 DOWN): initiate slats rotation (100% → 0%), time defined by Parameter No. 72

Action Table:

Action on Push Button	Blind Not Moving	Blind Moving Up	Blind Moving Down	Tilting Slats Ongoing
Short press (UP)	Start moving up	Stop moving	Stop moving	Stop tilting
Short press (DOWN)	Start moving down	Stop moving	Stop moving	Stop tilting
Long press (UP)	Start tilting slats	No action	No action	Continue tilting
Long press (DOWN)	Start tilting slats	No action	No action	Continue tilting
Release after long press	No action	Stop moving	Stop moving	Stop tilting

---

Manual Operation for Venetian Blinds with Toggle Switch

• Parameter No. 71 set to 1

• Parameter No. 1 set to 1

• Pressing a toggle switch on SW1 (up) starts upward movement until released.

• Pressing a toggle switch on SW2 (down) starts downward movement until released.

• When slats are at 100%, quick press of UP moves blind up.

• When slats are at 0%, quick press of DOWN moves blind down.

---

Slats Positioning

To achieve maximum precision when stopping via button, gateway, or remote control:

• When slats are in an intermediate position and receive a new command, they first rotate to 100%, then back to the target position.
• When moving down and limit switch is reached (or stopped), slats rotate to 100% then return to previous position.
• When moving up and stopped, slats rotate back to the previous position.

---

Main Applications

• Residential
• MDU (Multi Dwelling Units – apartments, condominiums, hotels, etc.)
• Light commercial (small office buildings, retail/restaurant/gas stations, etc.)
• Government/municipal
• University/college
• Farming

---

Integrations

Shelly Qubino Wave devices are built on Z-Wave, the world’s leading smart home technology. This means they work with all certified gateways supporting the Z-Wave protocol.

We regularly test compatibility across different Z-Wave gateways to ensure full functionality.

---

Simplified Internal Schematics

---

Device Electrical Interfaces

Inputs

• 2 switch/button inputs on screw terminals
• 2 power supply inputs on screw terminals: N and L

Outputs

• 2 relay outputs with power measurement on screw terminals

---

Connectivity

• Z-Wave: Unsecure, S0 Security, S2 Unauthenticated Security, S2 Authenticated Security

---

Safety Features

• Over-load detection
• Overheat detection

---

Supported Load Types

[Error: User '712020:515aa595-e304-41f3-886a-d9b6b0b7f5a3' does not have permission to view the page 'DEV:Supported load types'.]

---

User Interface

S Button and Operating Modes

1. Normal mode
2. Setting in progress mode
3. Setting mode (with S button)
   • Required to perform actions like inclusion, exclusion, or factory reset.
   • Limited-time operation; auto-returns to Normal mode after completion.
   • Entering Setting Mode:
     • Quickly press and hold the S button until the LED turns solid blue.
     • An additional quick press changes the menu (infinite loop).
     • Menu timeout: 10 seconds before returning to Normal state.

S Button Functions

• Manually add device to Z-Wave network
• Manually remove device from Z-Wave network
• Factory reset device

---

Functionality

Automatic Calibration

The device learns the position of the limit switches during calibration.

Note! For correct operation, calibration must be performed!

Note! The motor must have electronic or mechanical limit switches properly set before calibration.

---

Shutter Positioning Calibration (Shutter Mode)

• Parameter No. 71 = 0

Calibration with Gateway

1. Add the device to the Z-Wave network (inclusion).
2. Set Parameter No. 78 (forced Shutter calibration) to 1.
3. Device performs full cycle: up → down → up → down to 50%.
4. Check Parameter No. 78: value 2 = success, 3 or 4 = error.
5. Yellow LED should not blink.

If values 3 or 4: Verify full cycle execution, correct limit switch settings, and proper wiring.

Calibration with Push-Button (SW1)

1. Move blind to top position.
2. Press SW1 four times within 3 seconds.
3. Device starts calibration (4 cycles: up, down, up, down to 50%).
4. No time limit.

Calibration with S Button

1. Enter Setting mode (short press S button).
2. Hold S button until yellow LED appears (calibration selected).
3. Press S button for >2 seconds to start calibration.
4. Confirm yellow LED is stable (no blinking).

If yellow LED blinks: Check full cycle, limit switches, and wiring.

---

Slats Tilting Position Calibration (Venetian Mode)

• Parameter No. 71 = 1

After enabling venetian blind mode, calibrate slats positioning.

• Default rotation time: 1.5 seconds (adjustable via Parameter No. 72).

Steps:

1. Add and calibrate using the "Shutter positioning calibration" procedure.
2. Set Parameter No. 71 to 1 ("Venetian blinds").
3. Adjust Parameter No. 72:
   • Too short? Increase time.
   • Too long? Decrease time (if blind starts moving during slat rotation).
4. Repeat until slats position is accurate.

Note: Correct timing prevents unwanted blind movement during slat adjustment.

---

LED Signalisation

General Rules

• Press S button once to toggle between Normal and Setting modes.
• Solid LED = Setting mode (except plugs). Auto-returns to Normal after 10s.
• LED turns off after 30 min (unless woken by S button or power cycle).

Normal Mode LED Status

Condition	LED Behavior
Removed/Excluded / Not Calibrated	Blinking blue (10 min after power-on or S button press)
Removed/Excluded / Calibrated	Blinking blue & yellow (30 min after power-on, 10 min after S button press)
Added/Included / Not Calibrated	Blinking green (10 min after power-on or S button press)
Added/Included / Calibrated	Blinking green & yellow (30 min after power-on, 10 min after S button press)

Settings in Progress

Event	LED Behavior
Factory Reset & Reboot	Solid green (1 sec), then blue & red blinking (0.1s on/off, ~2 sec)
Adding/Removing	Blinking blue (Mode 2)
Shutter Calibration	Blinking yellow (Mode 2)

Settings Mode with S Button

Menu Selected	LED Behavior
Adding/Removing	Solid blue (max 10s)
Adding/Removing (during)	Blinking blue (Mode 3)
Factory Reset	Solid red (max 10s)
Factory Reset (during)	Blinking red (Mode 3)
Calibration	Solid yellow (max 10s)
Calibration (during)	Blinking yellow (Mode 3)

Alarm Mode

Alarm Type	LED Behavior
Over-current detected	Red blinking: 1x (0.2s on/off), 2s off → repeat
Overheat detected	Red blinking: 2x (0.2s on/off), 2s off → repeat
Power Supply Fault	Red blinking: 3x (0.2s on/off), 2s off → repeat

---

LED Blinking Modes

Mode	Blink Pattern
1	0.5s On / 2s Off
2	0.5s On / 0.5s Off
3	0.1s On / 0.1s Off
4	(1–6x: 0.2s On/Off) + 2s Off
5	0.2s Blue On / 0.2s Red On

---

Specifications

[Error: User '712020:515aa595-e304-41f3-886a-d9b6b0b7f5a3' does not have permission to view the page 'DEV:Technical Specifications'.]

---

Basic Wiring Diagram

[Error: User '712020:515aa595-e304-41f3-886a-d9b6b0b7f5a3' does not have permission to view the page 'DEV:Wiring diagrams'.]

---

Legend

Unable to render {include} – The included page could not be found.

---

About Z-Wave

Adding the Device to a Z-Wave® Network (Inclusion)

Note! The blind will move 2s up/down if the device is successfully added/removed.

Note! For S2 inclusion, enter the 5-digit PIN from the DSK label on the device or packaging.
IMPORTANT: Never lose the PIN.

SmartStart Inclusion

1. Scan the Z-Wave QR code on the device with a SmartStart-enabled gateway.
2. Connect device to power.
3. If blue LED blinks slowly → not added.
4. Addition starts automatically within seconds.
5. Blue LED blinks faster during inclusion.
6. Green LED blinks slowly upon successful addition.

Adding with S Button

1. Connect device to power.
2. Check if blue LED blinks slowly.
3. Enable add/remove mode on gateway.
4. Press and hold S button until LED turns solid blue.
5. Release, then press and hold (>2s) until blue LED blinks slowly → release to start learn mode.
6. Blue LED blinks faster during inclusion.
7. Green LED blinks slowly if successful.

Note: Setting mode times out after 10s.

Adding with Switch/Push-Button

1. Connect device to power.
2. Check if blue LED blinks slowly.
3. Enable add/remove mode on gateway.
4. Toggle switch/push-button 3 times within 3 seconds (must receive 3 on/off signals).
5. Blue LED blinks faster during inclusion.
6. Green LED blinks slowly if successful.

Learn Mode: State allowing device to receive network info from gateway.

---

Removing the Device from a Z-Wave® Network (Exclusion)

Note! Custom parameters remain unchanged after removal.

Note! Blind moves 2s up/down upon successful removal.

Removing with S Button

1. Connect device to power.
2. Check if green LED blinks slowly (device is added).
3. Enable add/remove mode on gateway.
4. Press and hold S button until LED turns solid blue.
5. Release, then press and hold (>2s) until blue LED blinks slowly → release to start learn mode.
6. Blue LED blinks faster during removal.
7. Blue LED blinks slower if successful.

Removing with Switch/Push-Button

1. Connect device to power.
2. Check if green LED blinks slowly.
3. Enable add/remove mode on gateway.
4. Toggle switch/push-button 3 times within 3 seconds.
5. Blue LED blinks faster during removal.
6. Blue LED blinks slower if successful.

---

Factory Reset

General

• Resets all custom parameters, kWh, associations, routing, HOME ID, NODE ID.
• Use only if gateway is missing/inoperable.

With S Button

1. Press and hold S button until LED turns solid blue.
2. Press S button multiple times until LED turns solid red.
3. Hold S button (>2s) until red LED blinks fast → release to start reset.
4. During reset: green (1s), then blue & red blink fast (~2s).
5. Blue LED blinks slowly if successful.

With Switch/Push-Button

Only possible within first minute after power-up.

1. Connect device to power.
2. Toggle switch/push-button 5 times within 3 seconds.
3. During reset: green (1s), then blue & red blink fast (~2s).
4. Blue LED blinks slowly if successful.

---

Z-Wave Security and Device Specific Key (DSK)

The device supports Security 2 (S2) with AES-128 encryption — the most secure IoT platform available.

• Supports S2 Authenticated, Unauthenticated, and Unsecure inclusion.
• For S2 inclusion, the DSK PIN (first five digits of DSK label) is required.
• DSK label is on the side of the device and inside the packaging.
• Do not remove the label.

QR Code Example:

• First 5 digits highlighted/underlined → PIN code.
• DSK may be used for out-of-band (OOB) authentication.

---

Z-Wave Parameters

[Error: Unable to render {include} – The included page could not be found.]

---

Z-Wave Command Class

[Error: Unable to render {include} – The included page could not be found.]

---

Z-Wave Notifications Command Class

[Error: Unable to render {include} – The included page could not be found.]

---

Z-Wave Associations

[Error: Unable to render {include} – The included page could not be found.]

---

Z-Wave Important Disclaimer

Z-Wave wireless communication may not always be 100% reliable. This device should not be used where life or valuable assets depend solely on its function. If unrecognized by your gateway, manually change device type and verify support for Z-Wave Plus™ multi-channel devices.

---

Troubleshooting

For help, visit our support portal: https://support.shelly.cloud/

---

Compatibility with Gateways

Gateway	Up	Down	SW Up	SW Down	W	kWh	Slats	SW Slats	Notes
Home Assistant	✅	✅	✅	✅	✅	✅	✅	✅
Fibaro HC 3 / Z-Wave engine 3	✅	✅	✅	✅	❌	❌	✅	✅
Homey	✅	✅	✅	✅	❌	❌	✅	✅
Homee Cube Gen 7	✅	✅	✅	✅	✅	✅	⚪	⚪	*1
Homee Cube Gen 5	✅	✅	⚪	⚪	⚪	⚪	⚪	⚪	*1, *2, *3
Smart Things	TBD	TBD	TBD	TBD	TBD	TBD	TBD	TBD	With Shelly Wave edge driver
Vera Ezlo	✅	✅	✅	✅	✅	✅	✅	✅
Cozify	✅	✅	✅	✅	✅	✅	✅	✅

Notes:
*1: Slats cannot be controlled via UI; position not visualized.
*2: UI reports sent only via buttons; slider sends to location but doesn’t refresh state.
*3: State refreshes only after stop button pressed.
*4: Device goes to position but state not reported.

---

Legend

Symbol	Meaning
✅	Working / Possible
⚪	Not Working / Not Possible
P	Partially
N/T	Not Tested
TBD	To be done

---

Function Definitions

Function	Meaning / Tested
On/Off	Responds to app UI On/Off command
SW On/Off	Reports On/Off changes via SW input
Dimming	Responds to app UI dimming command
SW Dimming	Reports dimming state change via SW input
Watts	Reports watts (unsolicited)
kWh	Reports kWh (unsolicited)
Up/Down	Responds to app UI Up/Down command
SW Up/Down	Reports Up/Down changes via SW input
Slats	Slats respond to app UI command
SW Slats	Slats report changes made via SW
D control	Detached mode: reports scene commands (single/double press, etc.)
D Binary	Detached mode: reports binary On/Off via SW input
Sensor #	Sensor report visible in gateway; type noted

---

Gateway Guides

Useful guides: Shelly Knowledge Base – Z-Wave

---

Compliance

• Wave Pro Shutter multilingual EU Declaration of Conformity (2025-07-23)
• Wave Pro Shutter UK PSTI ACT Statement of Compliance

---

Printed User Guide

Wave Pro Shutter US Print PDF