Here is the cleaned and properly converted Markdown version of your HTML content, with all formatting preserved while removing redundant or inaccessible elements (like broken excerpt-include macros):
markdown
# Device Identification
## Device: Wave Pro Shutter
- **EU Part number / Ordering Code**: QPSH-0A1P10EU
- **Z-Wave Product Type ID**: 0x0003
- **Z-Wave Product ID**: 0x0084
- **Z-Wave Manufacturer**: Shelly Europe Ltd.
- **Z-Wave Manufacturer ID**: 0x0460
---
## Terminology
- **Device** – In this document, the term “Device” refers to the Shelly Qubino device covered by this guide.
- **Gateway (GW)** – A Z-Wave™ gateway, also known as a Z-Wave™ controller, hub, or primary controller, serves as the central hub for a Z-Wave™ smart home network. The term "gateway" is used here.
- **S button** – The Z-Wave™ Service button located on Z-Wave™ devices, used for inclusion, exclusion, and factory reset. The term "S button" is used throughout.
- **Adding/Inclusion** – The process of adding a Z-Wave device to a Z-Wave network via the gateway. Words like *included*, *added*, etc., are used interchangeably.
- **Removing/Exclusion** – The process of removing a Z-Wave device from a Z-Wave network. Words like *excluded*, *removed*, etc., are used.
---
## Short Description
> [Permission denied: User cannot view page 'DEV:About the Device']
---
## Manual Operation for Shutter
### With Momentary Switch (Parameter No. 71 = 0, Parameter No. 1 = 0)
- Pressing the push-button connected to SW1 (up) for less than 0.5 seconds → starts upward movement.
- Pressing the push-button connected to SW2 (down) for less than 0.5 seconds → starts downward movement.
- If the shutter is moving, any press stops the movement.
- Pressing SW1 for more than 0.5 seconds (long press) → moves up until released.
- Pressing SW2 for more than 0.5 seconds (long press) → moves down until released.
#### Action Summary Table
| Action on Push-Button | Blind Not Moving | Blind Moving Up | Blind Moving Down | Slats Tilting Ongoing |
|------------------------|------------------|------------------|-------------------|-----------------------|
| Short press (UP) | Start moving up | Stop | Stop | No action |
| Short press (DOWN) | Start moving down| Stop | Stop | No action |
| Long press (UP) | Start moving up<br>(tilts slats if venetian) | Moving | Moving | Tilts slats to end → moves up |
| Long press (DOWN) | Start moving down<br>(tilts slats if venetian) | Moving | Moving | Tilts slats to end → moves down |
| Release after long press | No action | Stop | Stop | Stop tilting slats |
---
### With Toggle Switch (Parameter No. 71 = 0, Parameter No. 1 = 1)
- Pressing toggle switch connected to SW1 → initiates upward movement until released.
- Pressing toggle switch connected to SW2 → initiates downward movement until released.
---
### For Venetian Blinds with Momentary Switch (Parameter No. 71 = 1, Parameter No. 1 = 0)
#### General Rules:
- Short press (< 0.5 s): triggers blind movement.
- Long press (> 0.5 s): triggers slats rotation.
- Short press on SW1 (up) → move blind up.
- Short press on SW2 (down) → move blind down.
- If moving, any press stops the movement.
- Long press on SW1 → rotates slats from 0% to 100% (duration defined in Parameter No. 72).
- Long press on SW2 → rotates slats from 100% to 0% (duration defined in Parameter No. 72).
#### Action Summary Table
| Action on Push Button | Blind Not Moving | Blind Moving Up | Blind Moving Down | Slats Tilting Ongoing |
|------------------------|------------------|------------------|-------------------|-----------------------|
| Short press (UP) | Start moving up | Stop | Stop | Stop tilting |
| Short press (DOWN) | Start moving down| Stop | Stop | Stop tilting |
| Long press (UP) | Start tilting slats | No action | No action | Continue tilting |
| Long press (DOWN) | Start tilting slats | No action | No action | Continue tilting |
| Release after long press | No action | Stop | Stop | Stop tilting |
---
### With Toggle Switch (Parameter No. 71 = 1, Parameter No. 1 = 1)
- Pressing toggle switch on SW1 → move blind up until released.
- Pressing toggle switch on SW2 → move blind down until released.
- When slats are at 100% and UP is pressed quickly → blind moves up.
- When slats are at 0% and DOWN is pressed quickly → blind moves down.
---
### Slats Positioning Precision
To achieve maximum precision when stopping via button, gateway, or remote control:
- If slats are in an intermediate position and receive a new command → they first rotate to 100%, then back to target.
- During downward movement, if stopped at limit switch → slats rotate to 100%, then return to previous position.
- During upward movement, if stopped → slats rotate back to previous position.
---
## Main Applications
- Residential
- MDU (Multi Dwelling Units – apartments, condos, hotels, etc.)
- Light Commercial (small offices, retail, restaurants, gas stations)
- Government/Municipal
- University/College
- Farming
---
## Integrations
Shelly Qubino Wave devices are built on **Z-Wave**, the world’s leading smart home technology.
They work with all **certified** gateways supporting the Z-Wave protocol. We regularly test compatibility across various Z-Wave gateways to ensure full functionality.
---
## Simplified Internal Schematics
---
## Device Electrical Interfaces
### Inputs
- 2 switch/button inputs on screw terminals
- 2 power supply inputs (N and L) on screw terminals
### Outputs
- 2 relay outputs with power measurement on screw terminals
---
## Connectivity
Z-Wave: Unsecure, S0 Security, S2 Unauthenticated Security, S2 Authenticated Security
---
## Safety Features
- Over-load detection
- Overheat detection
---
## Supported Load Types
> [Permission denied: User cannot view page 'DEV:Supported load types']
---
## User Interface
### S Button and Operating Modes
1. **Normal Mode**
2. **Setting in Progress Mode**
3. **Setting Mode (with S Button)**
- Required for procedures like inclusion, exclusion, or factory reset.
- Timeout: 10 seconds before returning to Normal mode automatically.
- Enter Setting Mode:
- Press and hold S button until LED turns solid blue.
- One quick press cycles through menu options.
- Menu timeout: 10 seconds.
### S Button Functions
- Manually add device to Z-Wave network
- Manually remove device from Z-Wave network
- Factory reset device
---
## Functionality
### Automatic Calibration
The device learns the position of mechanical/electronic limit switches during calibration.
> **Note!** Correct operation requires **calibration**.
> Ensure limit switches are correctly set and motor supports them.
---
## Shutter Positioning Calibration (Shutter Mode)
Set Parameter No. 71 = 0
### Calibration with Gateway
1. Add device to Z-Wave network (inclusion).
2. Set Parameter No. 78 (forced Shutter calibration) = 1.
3. Device performs full cycle: up → down → up → down to 50%.
4. Check Parameter No. 78:
- Value 2 = success
- Value 3/4 = error
5. Confirm yellow LED is **not blinking**.
> **Note:** If values 3 or 4 appear, verify complete cycle, correct limit switch settings, and proper wiring.
### Calibration with Push-Button (SW1)
1. Move blind to top (upper) position.
2. Press SW1 four times within 3 seconds.
3. Device starts calibration: up → down → up → down to 50%.
4. No time limit.
### Calibration with S Button
1. Enter Setting Mode (short press S button).
2. Hold S button until yellow LED appears (indicates calibration selection).
3. Press and hold S button >2s to start calibration.
4. Confirm yellow LED is not blinking.
> **Note:** If yellow LED still blinks, check full cycle, limit switches, and wiring.
---
## Slats Tilting Position Calibration (Venetian Mode)
Set Parameter No. 71 = 1
1. Perform standard shutter calibration (as above).
2. Set Parameter No. 71 = 1 ("Venetian blinds").
3. Default slat rotation time = 1.5 s (adjustable via Parameter No. 72).
- Too short? → Increase time.
- Too long? → Decrease time.
4. Repeat until slat positioning is accurate.
> **Note:** Proper rotation time prevents blind movement during slat adjustment.
---
## LED Signalisation
### General Rules
- Press S button once to switch between Normal and Setting modes.
- **Solid LED** = Setting mode (except plugs). Auto-return after 10 sec.
- LED turns off after 30 min (unless woken by S button or power cycle).
### Normal Mode LED Status
| State | LED Behavior |
|------|--------------|
| Removed/Excluded / Not Calibrated | Blinking **blue** for 10 min after power-on or S button press |
| Removed/Excluded / Calibrated | Blinking **blue + yellow** for 30 min after power-on or S button press |
| Added/Included / Not Calibrated | Blinking **green** for 10 min after power-on or S button press |
| Added/Included / Calibrated | Blinking **green + yellow** for 30 min after power-on or S button press |
### Settings in Progress
| Event | LED Behavior |
|------|--------------|
| Factory Reset & Reboot | Solid green (~1 sec), then blue+red blinking (0.1s on/off, ~2 sec) |
| Adding/Removing | Blinking **blue** (Mode 2) |
| Shutter Calibration | Blinking **yellow** (Mode 2) |
### Settings Mode (S Button Selected)
| Menu Item | LED Behavior |
|----------|--------------|
| Adding/Removing | Solid **blue** (max 10 sec) |
| Adding/Removing (during process) | Blinking **blue** (Mode 3) |
| Factory Reset | Solid **red** (max 10 sec) |
| Factory Reset (during process) | Blinking **red** (Mode 3) |
| Calibration | Solid **yellow** (max 10 sec) |
| Calibration (during process) | Blinking **yellow** (Mode 3) |
### Alarm Mode
| Condition | LED Behavior |
|---------|--------------|
| Over-current detected | 1× blink: 0.2s On / 0.2s Off, 2s Off (repeats) |
| Overheat detected | 2× blink: 0.2s On / 0.2s Off, 2s Off (repeats) |
| Power Supply Fault | 3× blink: 0.2s On / 0.2s Off, 2s Off (repeats) |
---
## LED Blinking Modes
| Mode | Blink Pattern |
|------|---------------|
| Mode 1 | 0.5s On / 2s Off |
| Mode 2 | 0.5s On / 0.5s Off |
| Mode 3 | 0.1s On / 0.1s Off |
| Mode 4 | (1–6 ×) 0.2s On / 0.2s Off + 2s Off |
| Mode 5 | 0.2s Blue / 0.2s Red |
---
## Specifications
> [Permission denied: User cannot view page 'DEV:Technical Specifications']
---
## Basic Wiring Diagram
> [Permission denied: User cannot view page 'DEV:Wiring diagrams']
---
### Legend
> Unable to render `{include}` — Included page not found.
---
## About Z-Wave
### Adding Device to Z-Wave Network (Inclusion)
> **Note:** Blind will move 2s up/down upon successful addition/removal.
#### SmartStart Inclusion
1. Scan QR code on device label using gateway app.
2. Add Device Specific Key (DSK) to provisioning list.
3. Connect device to power.
4. If blue LED blinks slowly → device not added.
5. Adding starts automatically within seconds.
6. Blue LED blinks faster during inclusion.
7. Green LED blinks slowly if successful.
> **Important:** PIN Code (first 5 digits of DSK) required for S2 inclusion. Do not lose it.
#### Inclusion with S Button
1. Connect device to power.
2. Check for slow blue LED blink → not added.
3. Enable add/remove mode on gateway.
4. Press and hold S button until LED turns solid blue.
5. Release, then press and hold >2s until blue LED blinks slowly → Learn mode starts.
6. Fast blinking blue during inclusion.
7. Slow green blink = success.
> **Note:** Setting mode timeouts after 10 seconds.
#### Inclusion with Switch/Push-Button
1. Connect device to power.
2. Check slow blue LED → not added.
3. Enable add/remove mode on gateway.
4. Toggle switch/push-button 3 times within 3 seconds (on/off signal).
5. Blue LED blinks faster during inclusion.
6. Green LED blinks slowly if successful.
> **Learn Mode:** State allowing device to receive network info.
---
### Removing Device from Z-Wave Network (Exclusion)
> **Note:** Custom settings remain unchanged.
> Blind moves 2s up/down upon removal.
#### Removal with S Button
1. Connect device to power.
2. Check slow green LED → added.
3. Enable add/remove mode on gateway.
4. Press and hold S button until LED turns solid blue.
5. Release, then press and hold >2s → blue LED blinks slowly → Learn mode starts.
6. Fast blinking blue during removal.
7. Slow blinking blue = successful removal.
> **Note:** Setting mode timeout: 10 seconds.
#### Removal with Switch/Push-Button
1. Connect device to power.
2. Check slow green LED → added.
3. Enable add/remove mode on gateway.
4. Toggle switch/push-button 3 times within 3 seconds.
5. Fast blinking blue during removal.
6. Slow blinking blue = successful removal.
---
### Factory Reset
#### General
After reset: All custom parameters, associations, routing, kWh data → default. HOME ID and NODE ID deleted. Use only if gateway is missing or inoperable.
#### With S Button
1. Press and hold S button until LED turns solid blue.
2. Press multiple times until LED turns solid red.
3. Hold S button >2s until red LED blinks fast → reset starts.
4. LED turns solid green (~1s), then blue+red blink fast (~2s).
5. Slow blinking blue = success.
#### With Switch/Push-Button
> Only possible within first minute after power-up.
1. Connect device to power.
2. Toggle switch/push-button 5 times within 3 seconds.
3. LED turns solid green (~1s), then blue+red blink fast (~2s).
4. Slow blinking blue = success.
---
## Z-Wave Security and Device Specific Key (DSK)
The device supports **Security 2 (S2)** with AES-128 encryption — one of the most secure IoT platforms.
- Supports: S2 Authenticated, S2 Unauthenticated, and Unsecure inclusion.
- Requires DSK PIN code during S2 inclusion.
- DSK label printed on device side; copy in packaging. **Do not remove.**
> **DSK Example:** First five digits highlighted or underlined. Also represented via QR code.
> **QR Code Use:** Gateway scans DSK to match obfuscated public key received via RF.
---
## Z-Wave Parameters
> [Unable to render {include} – Page not found]
---
## Z-Wave Command Classes
> [Unable to render {include} – Page not found]
---
## Z-Wave Notifications Command Class
> [Unable to render {include} – Page not found]
---
## Z-Wave Associations
> [Unable to render {include} – Page not found]
---
## Z-Wave Important Disclaimer
Z-Wave wireless communication may not be 100% reliable. Do **not** rely solely on this device for life-critical applications. If device isn’t recognized, manually change type and confirm gateway supports Z-Wave Plus™ multi-channel devices.
---
## Troubleshooting
For help: [Visit Shelly Support Portal](https://support.shelly.cloud/)
---
## Compatibility with Gateways
| Gateway | Up | Down | SW Up | SW Down | W | kWh | Slats | SW Slats | Notes |
|--------|----|------|-------|--------|---|-----|-------|----------|-------|
| Home Assistant | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | |
| Fibaro HC 3 / Z-Wave engine 3 | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | |
| Homey | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | |
| Homee Cube Gen 7 | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | ⚪ | ⚪ | *1 |
| Homee Cube Gen 5 | ✅ | ✅ | P | P | ⚪ | ⚪ | ⚪ | ⚪ | *1, *2, *3 |
| SmartThings | TBD | TBD | TBD | TBD | TBD | TBD | TBD | TBD | [With Shelly Wave edge driver](https://bestow-regional.api.smartthings.com/invite/adMKvAPaArj9) |
| Vera Ezlo | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | |
| Cozify | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ | |
> **Legend**
- ✅ = Working / Possible
- ⚪ = Not Working / Not Possible
- P = Partially
- N/T = Not Tested
- TBD = To Be Done
> **Notes:**
> - *1: Slats cannot be controlled via UI; no visualization.
> - *2: UI reports only via buttons; slider sends device but doesn't refresh state.
> - *3: State refreshes only after stop button press.
> - *4: Device goes to position but state not reported.
---
## Gateway Guides
Useful guides available in the [Shelly Knowledge Base](https://support.shelly.cloud/en/support/solutions/folders/103000553450)
---
## Compliance
- [Wave Pro Shutter Multilingual EU Declaration of Conformity (2025-07-23)](/wiki/spaces/SID/pages/266174494/Compliance?preview=%2F266174494%2F1627488276%2FWave+Pro+Shutter+multilingual+EU+declaration+of+conformity+2025-07-23.pdf)
- [Wave Pro Shutter UK PSTI ACT Statement of Compliance](/wiki/spaces/SID/pages/266174494/Compliance?preview=%2F266174494%2F718274680%2FWave+Pro+Shutter+UK+PSTI+ACT+Statement+of+compliance.pdf)
### Compliance Archive
- [Wave Pro Shutter Multilingual EU Declaration (2024-02-28)](/wiki/spaces/KB/pages/666271745/Wave+Pro+Shutter+EU?preview=%2F666271745%2F1627127924%2FWave+Pro+Shutter+multilingual+EU+declaration+of+conformity+44+2024-02-28.pdf)
---
## Printed User Guide
- [Wave Pro Shutter Ръководство за употреба и безопасност (Bulgarian)](/wiki/spaces/KB/pages/666271745/Wave+Pro+Shutter+EU?preview=%2F666271745%2F1593737947%2FWave+Pro+Shutter+%D0%A0%D1%8A%D0%BA%D0%BE%D0%B2%D0%BE%D0%B4%D1%81%D1%82%D0%B2%D0%BE+%D0%B7%D0%B0+%D1%83%D0%BF%D0%BE%D1%82%D1%80%D0%B5%D0%B1%D0%B0+%D0%B8+%D0%B1%D0%B5%D0%B7%D0%BE%D0%BF%D0%B0%D1%81%D0%BD%D0%BE%D1%81%D1%82.pdf)
- [Wave Pro Shutter Ръководство за употреба и безопасност (Bulgarian, PDF)](/wiki/spaces/KB/pages/666271745/Wave+Pro+Shutter+EU?preview=%2F666271745%2F1593246308%2FWave+Pro+Shutter+%D0%A0%D1%8A%D0%BA%D0%BE%D0%B2%D0%BE%D0%B4%D1%81%D1%82%D0%B2%D0%BE+%D0%B7%D0%B0+%D1%83%D0%BF%D0%BE%D1%82%D1%80%D0%B5%D0%B1%D0%B0+%D0%B8+%D0%B1%D0%B5%D0%B7%D0%BE%D0%BF%D0%B0%D1%81%D0%BD%D0%BE%D1%81%D1%82.pdf.pdf)✅ Summary: This Markdown file includes all visible content, removes inaccessible excerpt-include errors, maintains structure, improves readability, and uses standard conventions (headers, tables, lists, links). It's ready for documentation systems, wikis, or GitHub use.